DR 4700 AG
DR 4720 AG
DR4700AG
DR4700
DR4720AG
DR4720

Temperature Transmitter DR 4700

Temperature Measuring with Pt100/Pt1000-Sensors

The Temperature Transmitter DR 4700 converts the sensor signal on input to temperature linear standard signal 0/4 to 20 mA or 0 to 5/10 V.

Extensive range selection
Measurement range within -100 to +600 °C for Pt100 and Pt1000 sensors
Easy selection of configuration
Measurement range, type of sensor, sensor connection and output signal can be easily set by using DIP switch
Universal power supply for 20 to 253 V AC/DC
Applicable world-wide for all common supply voltages
3-port isolation
Protection against erroneous measurements due to parasitic voltages or ground loops
Ultra small sized housing
12.5 mm housing with plug-in screw terminal blocks
Protective Separation
Protects service personnel and downstream devices against impermissibly high voltage
Maximum reliability
No maintenance costs
5 Years Warranty
Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)

Due to the easy selection of the input and output ranges, the new universal power supply and the ultra-small housing the Temperature Transmitter is suitable for flexible use. High reliability and Protective 3-Port-Separation are further characteristics that make the DR 4700 unrivaled.

The configuration of measurement range can be easily set within -100 to +600 °C by using DIP switch. Subsequent readjustment after range selection or measured range compensation can then be performed at the Zero/Span potentiometers on the front panel. Alternatively, the Temperature Transmitter is also available customer-specific adjusted.

The small housing with 12.5 mm width saves space in your switch cabinet and facilitates by the practical plug-in screw terminal blocks the assembly. For range setting a simple housing unblocking is installed which makes it possible to reach easily all control elements on the mounting rail.

The new universal power pack for 20 to 253 V AC/DC means the DR 4700 can be used anywhere in the world, with all mains power supplies. The unit’s high efficiency contributes significantly to reducing the unit’s own heat generation. This is reflected in extremely high reliability and long-term stability.

Product line

Product line DR 4700
Devices	Order No.
Temperature transmitter, min. span 50 K configurable (0 to 100°C pre adjusted)	DR 4700 AG
Temperature transmitter, min. span 25 K configurable (0 to 100°C pre adjusted)	DR 4720 AG

Downloads / Links

Data Sheet

Additional Documents

Tender specification (26.0 KiB)

Request offer

Technical Data

Input

Input signal	Pt 100 / Pt 1000, switchable
Sensor connection	2-wire-, 3-wire-, 4-wire
Measuring range
Zero	–100 °C,– 50 °C, 0 °C, 50 °C, switchable with Potentiometer ZERO 0 to 50 °C adjustable
Span	DR 4700 AG: 50 K, 100 K, 200 K, 300 K, switchable DR 4720 AG: 25 K, 50 K, 100 K, 150 K, switchable with Potentiometer SPAN 100 to 200 % of span adjustable
Sensor wire resistance	< 25 Ohm per wire
Sensor current	1mA / 0.1 mA
Sensor diagnostic	Sensor / wire break

Output

Output signal	0 to 20 mA, 0 to 5 V, 0 to 10 V switchable 4 to 20 mA, 1 to 5 V, 2 to 10 V
Load	Current output Voltage output	≤ 12 V (600 Ohm at 20 mA) ≤ 5 mA (2 kOhm at 10 V)
Residual ripple	< 10 mVrms
Sensor break action	Current output Voltage output	≥ 22 mA ≥ 11 V

General Data

Linearity	< 0.2 % of measuring span
Temperature coefficient 1)	< 150 ppm/K
Calibration	Max. of ± 0.1 °C or 0.1 % of measuring span
Response time T₉₉	< 20 ms
Test voltage	4 kV AC, 50 Hz, 1 min., input against output against power supply
Working voltage 2) (Basic Insulation)	600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1
Protection against electrical shock 2)	Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
Ambient temperature	Operation Transport and storage	–10 to +60 °C (+14 to +140 °F) –20 to +80 °C (–4 to +176 °F)
Power supply	20 to 253 V AC/DC,	AC 48 to 62 Hz, approx. 3 VA DC approx. 1.5 W
EMC 3)	EN 61326-1
Construction	12.5 mm (0.49") housing, protection type: IP 20 mounting on 35 mm DIN rail acc. to EN 60715
Weight	Approx. 100 g

Factory setting: Input: Pt100, 4-wire, Output: 0 to 20 mA

Average TC related to full scale value in specified operating temperature range, reference temperature 23 °C
For applications with high working voltages, ensure there is sufficient spacing or isolation from neighboring devices and protection against electric shocks.
Minor deviations possible during interference