Devices from the 6mm Series
| Input: | 0(4) to 20 mA, ±20 mA, 0 to 10 mA, ±10 mA, ABS 20 mA 0 to 10 V, ±10 V, 0 to 5 V, ±5 V, ABS 10 V 4 to 20 mA / NE43 |
| Output relay: | 250 V AC, 30 V DC, 2 A |
| Power supply | 24 V DC |
| Features: |
Signal on In-Rail-Bus E (supply circuit) at device failure, cable break und short circuit Housing width: 6.2 mm |
| Input | 0 to 5 A AC/DC 0 to 150 mV |
| Output relay | 250 V AC, 30 V DC, 2 A |
| Power supply | 24 V DC |
| Features: |
Group message at In-Rail-Bus E at device failure and alarm Housing width: 6.2 mm |
| Inputs: | 0...20 mA, 4...20 mA, 0...5 V, 0...10 V |
| Outputs: | 0...20 mA, 4...20 mA, 0...5 V, 0...10 V |
| Power Supply: | 24 V DC via In-Rail-Bus |
| Features: |
Calibrated signal setting, protective separation, housing width: 6.2 mm |
| Input: | 0 to ±20 mA, 0 to ±10 mA, 0 to ±10 V, 0 to ±5 V, live/dead-zero |
| Output: | 0 to ±20 mA, 0 to ±10 mA, 0 to ±10 V, 0 to ±5 V, live/dead-zero |
| Power supply: | 24 V DC |
| Features: | calibrated signal setting, zero/span compensation, protective separation, housing width: 6.2 mm |
| Input: | 0 to 20 mA, 4 to 20 mA, 0 to 10 V, 2 to 10 V, calibrated switchable |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 10 V, 2 to 10 V, calibrated switchable |
| Power supply: | 24 V DC |
| Features: | Protective separation, housing width: 6.2 mm |
| Input: | 0/4 to 20 mA | Energization of 2-wire transmitters |
| Output: | 0/4 to 20 mA | Bidirectional HART communication |
| Power supply: | 24 V DC | |
| Features: | Protective separation, housing width: 6.2 mm | |
| Input: | NAMUR, SN, S0, DC sensor, contact, V AC/DC, PNP, NPN and Push-Pull |
| Output relay: | 250 V AC, 30 V DC, 2 A |
| Power supply: | 24 V DC |
| Features: |
Signal on In-Rail-Bus E (supply circuit) at device failure, cable break und short circuit Housing width: 6.2 mm |
| Input: | 0(4) to 20 mA | 1- or 2-channel |
| Output: | 0(4) to 20 mA | |
| Voltage drop: | < 2.3 V | |
| Features: | Protective separation, housing width: 6.2 mm | |
| Input signal: | 0 to 20 mA, 4 to 20 mA 0 to 10 V, 2 to 10 V 0 to 5 V, 1 to 5 V |
| Bus protocol: | Modbus RTU |
| Power supply: | 24 V DC |
| Features: | Protective Separation, housing width: 6.2 mm |
| Input: | 0 to 10 V 0 to 20 mA |
| Bus connection: | Modbus RTU |
| Power supply: | 24 V DC |
| Features: | Protective 5 port separation up to 300 V AC/DC Housing width: 6.2 mm |
| Sensor input: | Standard signals: 0/4 to 20 mA, 0/2 to 10 V, 0/1 to 5V Current: ±1 mA, ±20 mA, ±100 mA Voltage: ±1 V, ±10 V, ±100 V, ±300 V mV/Shunt Voltage: ±50 mV, ±100 mV, ±500 mV Resistance: 5 kΩ, 20 kΩ, 100 kΩ Potentiometer: 500 Ω, 3 kΩ, 50 kΩ, 100 kΩ Pt: Pt100 ... Pt 10000, JPt50, JPt100 Ni: Ni100 ... Ni1000 KTY: 66 Industrietypen Thermocouple: A,B,C,D,E,J,K,L,N,R,S,T,U Binary-/Switching input: PNP, NPN, Push-Pull, Contact, NAMUR, S0-Switch |
| Bus protocol: | Modbus RTU |
| Power supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |
| Input: | 5V / 12V / 24V level binary, frequency, counter |
| Output: | Open collector binary, frequency, pulse, PWM |
| Bus protocol: | Modbus RTU |
| Power supply: | 24 V DC |
| Features: | Protective Separation, housing width: 6.2 mm |
| Output: | SPST Power Relay 250 V AC / 30 V DC / 2 A |
| Bus protocol: | Modbus RTU |
| Power supply: | 24 V DC |
| Features: | Protective Separation, housing width: 6.2 mm |
| Input: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 1 to 5 V, 0 to 10 V, 2 to 10 V |
| Output 1: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 1 to 5 V, 0 to 10 V, 2 to 10 V |
| Output 2: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 1 to 5 V, 0 to 10 V, 2 to 10 V |
| Power supply: | 24 V DC |
| Features: | Calibrated signal setting, protective separation, housing width: 6.2 mm |
| Input: | 0 to 20 mA, 4 to 20 mA, 0 to 10 V, 2 to 10 V, calibrated switchable |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 10 V, 2 to 10 V, calibrated switchable |
| Power supply: | 24 V DC |
| Features: | Calibrated signal setting, protective separation, housing width: 6.2 mm |
| Input: | 0 to ±60 mV, 0 to ±100 mV, 0 to ±150 mV, 0 to ±250 mV, 0 to ±300 mV, 0 to ±500 mV |
| Output: | 0 to ±20 mA, 0 to ±10 mA, 0 to ±10 V, 0 to ±5 V, live/dead-zero |
| Power supply: | 24 V DC |
| Features: | signal setting with DIP switches, zero/span compensation, protective separation, housing width: 6.2 mm |
| Sensor Input: | Resistors: Pt 100, Pt 200, Pt 500, Pt 1000, Ni 100, Ni 200, Ni 500, Ni 1000; Thermocouple: B, E, J, K, L, N, R, S, T, U, W5Re_W26Re, W3Re_W25Re; KTY, resistor, mV and potentiometer measuring |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 10 mA, 2 to 10 mA 0 to 5 V, 0 to 10 V, 1 to 5 V, 2 to 10 V |
| Measurement Ranges: | -270 to +2315 °C, according to sensor type |
| Power Supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |
| Sensor Input: | Pt 100, Pt 200, Pt 500, Pt 1000, Pt 2000 JPt 50, JPt 100 |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V |
| Measurement Ranges: | -200 to +850 °C, according to sensor type |
| Power Supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |
| Sensor Input: | Ni 100, Ni 200, Ni 500, Ni 1000 acc. DIN 43760 (TK6180) Ni 120 (TK6720), Ni 1000 (TK5000), Ni 1000 (TK6370) |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V |
| Measurement Ranges: | -50 to +250 °C, according to sensor type |
| Power Supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |
| Sensor Input: | Measuring input for all KTY temperature sensors |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V |
| Measurement Ranges: | -50 to +300 °C, according to sensor type |
| Power Supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |
| Sensor Input: | Thermocouple Type A, B, C, D, E, J, K, L, N, R, S, T, U |
| Output: | 0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V |
| Measurement Ranges: | -200 to +2500 °C, according to type of thermocouple |
| Power Supply: | 24 V DC |
| Features: | Protective Separation, Housing width: 6.2 mm |